Easy To Download Cisco 300-615 Exam Dumps Updated 223 Questions
New Updated 300-615 Exam Questions 2026
Cisco 300-615 exam covers topics such as troubleshooting routing protocols, troubleshooting overlay protocols, troubleshooting virtualization, and troubleshooting data center automation and orchestration. 300-615 exam also assesses the candidate's ability to identify and resolve common data center infrastructure issues, such as network congestion, connectivity problems, and performance issues.
Cisco 300-615 certification exam is a valuable credential for IT professionals who work with Cisco data center technologies. It demonstrates the candidate's ability to troubleshoot complex data center infrastructure issues and provides an opportunity for career advancement and increased earning potential. With this certification, candidates can differentiate themselves in the competitive job market and demonstrate their expertise in data center infrastructure troubleshooting.
NEW QUESTION # 66
An engineer troubleshoots a packet flow from an access leaf to a spine. Which EVPN routes are expected on this connection?
- A. EVPN Type 1-5
- B. EVPN Type 0 and 16
- C. EVPN Type 0, 9, and 15
- D. EVPN Type 9-15
Answer: A
Explanation:
Section: Network
Explanation
NEW QUESTION # 67 
Refer to the exhibit. A PC belongs to VLAN 68. The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?
- A. Replace HSRP with GLBP.
- B. Remove the HSRP configuration.
- C. Configure ip arp synchronization on both switches.
- D. Enable the peer-gateway feature.
Answer: D
Explanation:
Section: Network
Explanation
Explanation/Reference: https://community.cisco.com/t5/networking-documents/peer-gateway-feature-on-the-nexus-7000/ ta-p/3113290
NEW QUESTION # 68
Refer to the exhibit.
A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic. Which action resolves the issue?
- A. Shut and no shut the interfaces to the FEX.
- B. Roll back to the original image.
- C. Reload the switch.
- D. Enable ISSD after the downgrade is complete.
Answer: D
NEW QUESTION # 69
Refer to the exhibit.
A Postman call to a Cisco APIC fails. The access credentials were confirmed to be configured as expected.
Which action resolves the issue?
- A. Change operation type to POST
- B. Change the IP address to a domain name
- C. Modify the target protocol type to XML
- D. Modify the protocol to HTTP
Answer: A
NEW QUESTION # 70
A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.
Answer:
Explanation:
NEW QUESTION # 71
Refer to the exhibit.
A PC belongs to VLAN 68 The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?
- A. Replace HSRP with GLBP
- B. Configure ip arp synchronization on both switches.
- C. Enable the peer-gateway feature
- D. Remove the HSRP configuration
Answer: C
Explanation:
I assume that the PC is sending traffic with destination MAC of Nexus physical interfaces. If more snap shots about this question are available, please share.
NEW QUESTION # 72
Refer to the exhibit.
vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)
- A. Configure vPC peer link and vPC peer keepalive correctly.
- B. Match vPC domain ID between the two devices.
- C. Activate VLANs on the vPC.
- D. Configure IP address on the interface.
- E. Configure one of the switches as primary for the vPC.
Answer: B,C
Explanation:
The answer is Match vPC domain ID between the two devices; Activate VLANs on the vPC because Cisco Nexus and ACI forwarding depends on exact agreement between the devices participating in the feature. The scenario references vPC; those technologies fail in predictable ways when required parameters do not match or when the required control-plane advertisement is absent. In DCIT troubleshooting, the engineer should identify the failed dependency, correct that dependency, and then verify the operational table that proves the fix. For example, vPC and EVPN checks focus on consistency, VNI/VRF bindings, peer-gateway behavior, and host-route advertisement; routing checks focus on neighbor state, MTU, timers, authentication, next-hop, and route preference. The selected answer addresses the dependency that blocks forwarding. The distractors are plausible because they touch related features, but they do not resolve the specific failure condition. Post- change validation should include protocol state, learned endpoint or route entries, and a traffic test across the affected path.
NEW QUESTION # 73
Refer to the exhibit.
During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.
- A. Set SLOT-1 Sync Mode to "Auto"
- B. Reconfigure the Drive Type from "Removable" to "Non-Removable"
- C. Insert an SD card into SLOT-2
- D. Configure the RAID that is associated with the card.
Answer: C
NEW QUESTION # 74
Drag and Drop Question
A Cisco Nexus 9000 Series Switch crashes and fails to boot. An engineer must recover the switch and investigate the issue. The switch uses 172.20.50.213/24 IP address for management and its default gateway is 172.20.50.254. Drag and drop the steps for recovering the Cisco Nexus
9000 Series Switch from the left onto the right. Not all steps are used.
Answer:
Explanation:
NEW QUESTION # 75
Refer to the exhibit. The VXLAN configuration fails.
Which action do you take to resolve the issue?
- A. Change the multicast address in the 232.0.0.0/8 range.
- B. Enable dense mode on loopback1.
- C. Use a transit interface as the source interface.
- D. Change the mask of loopback1 to 255.255.255.255.
Answer: D
NEW QUESTION # 76
A Cisco Nexus 9000 Series Switch crashes and fails to boot. An engineer must recover the switch and investigate the issue. The switch uses 172.20.50.213/24 IP address for management and its default gateway is
172.20.50.254. Drag and drop the steps for recovering the Cisco Nexus 9000 Series Switch from the left onto the right. Not all steps are used.
Select and Place:
Answer:
Explanation:
Explanation:
The answer is the drag-and-drop mapping shown in the answer key because Cisco Nexus and ACI forwarding depends on exact agreement between the devices participating in the feature. The scenario references Cisco Nexus, Nexus 9000, Cisco Nexus 9000; those technologies fail in predictable ways when required parameters do not match or when the required control-plane advertisement is absent. In DCIT troubleshooting, the engineer should identify the failed dependency, correct that dependency, and then verify the operational table that proves the fix. For example, vPC and EVPN checks focus on consistency, VNI/VRF bindings, peer- gateway behavior, and host-route advertisement; routing checks focus on neighbor state, MTU, timers, authentication, next-hop, and route preference. The selected answer addresses the dependency that blocks forwarding. The distractors are plausible because they touch related features, but they do not resolve the specific failure condition. Post-change validation should include protocol state, learned endpoint or route entries, and a traffic test across the affected path.
NEW QUESTION # 77
A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?
- A. Set the same WWPN pools for vHBA adapters
- B. Set the same WWNN pools for vHBA adaptor
- C. Set the boot LUN to the lowest LUN ID in the storage array
- D. Set the boot LUN to the highest LUN ID in the storage array
Answer: B
NEW QUESTION # 78
Refer to the exhibit.
A Cisco UCS Fabric Interconnect fails during the upgrade process. The working images of the fabric interconnect are stored on the bootflash. Which set of commands recovers the fabric interconnect?
- A. loader> dir
loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
switch(boot)# init system
switch(boot)# reload
switch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin - B. loader> dir
loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
switch(boot)# init system
switch(boot)# reload
switch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin - C. loader> dir
loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
switch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.bin switch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin - D. loader> dir
loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
switch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.bin switch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin
Answer: C
NEW QUESTION # 79
The Cisco Nexus switch is connected to a peer switch that is not running Cisco NX-OS. The switches are connected using port channel and are experiencing packet loss. Which action should be performed on the Cisco Nexus switch ports to resolve this issue?
- A. Turn off lacp suspend-individual.
- B. Turn on lacp graceful-convergence.
- C. Turn on lacp suspend-individual.
- D. Turn off lacp graceful-convergence.
Answer: D
NEW QUESTION # 80
Refer to the exhibit.
Refer to the exhibit. The expected routes are not being leaked as expected from VRF RED to VRF BLUE. Which action resolves the issue?
- A. Include the "le 32" knob under the RED_TO_BLUE_ACL prefix list.
- B. Set the community to 65000:65000 under the route map.
- C. Configure VRF BLUE under the BGP configuration.
- D. Change the route targets under the VRFs.
Answer: B
NEW QUESTION # 81
Refer to the exhibit.
A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic. Which action resolves the issue?
- A. Shut and no shut the interfaces to the FEX.
- B. Enable ISSD after the downgrade is complete.
- C. Reload the switch.
- D. Roll back to the original image.
Answer: D
NEW QUESTION # 82
Refer to the exhibit. A newly deployed Cisco APIC1 fails to discover a Cisco Nexus Series Switch. Which configuration resolves the issue?
- A. Leaf101# setup-clean-config.sh
Leaf101# reload - B. Leaf101#(config)# no boot nxos
Leaf101# copy running-config startup-config
Leaf101# reload - C. APIC1# acidiag touch clean
APIC1# acidiag touch setup
APIC1# acidiag reboot - D. APIC1# acidiag restart mgmt
APIC1# acidiag reboot
Answer: A
NEW QUESTION # 83 
Refer to the exhibit. A network engineer configures an authentication domain through an LDAP provider on the Cisco UCS Manager for users from different companies to log into their respective organizations created in the UCS Manager. The engineer tests the configuration and notices that any user has login access to any organization in the UCS Manager. Which action should be taken to resolve the issue?
- A. Configure the Filter field with the company
- B. Configure the Attribute field with sAMAccountName=$company
- C. Configure the Filter field with sAMAccountName=$company
- D. Configure the Attribute field with the company
Answer: C
Explanation:
Configure the Filter field with sAMAccountName=$company is the appropriate UCS remediation because the symptom maps to a specific managed object rather than a generic server failure. Cisco UCS abstracts hardware through service profiles and policies; therefore, issues involving UCS, UCS Manager, LDAP must be corrected where UCS Manager programs the adapter, boot target, firmware, management certificate, pool qualification, or fabric interconnect state. The selected answer restores that programming path. The other options may appear plausible, but they do not correct the object that UCS uses to derive operational state. For example, boot failures require the correct vHBA/iSCSI target and LUN policy, discovery issues require the proper physical and management path, and firmware failures require the documented recovery action for the failed FSM stage. The correct validation is to inspect the associated fault, confirm inventory acknowledgment, verify the policy under the service profile or equipment tree, and then recheck boot or connectivity behavior after the FSM completes.
NEW QUESTION # 84
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)
- A. F-Series module
- B. FCoE license
- C. STORAGE-ENT license
- D. M-Series module
- E. ESSENTIALS license
Answer: A,B
Explanation:
Section: Storage Network
NEW QUESTION # 85
......
Updated Free Cisco 300-615 Test Engine Questions with 223 Q&As: https://www.dumpsreview.com/300-615-exam-dumps-review.html
The Best CCNP Data Center 300-615 Professional Exam Questions: https://drive.google.com/open?id=18IxJUvYaKGnzLpxBdyknO9ZbSaHQ9ne1
