NACE-CIP1-001 Revolutionary Guide To Exam NACE Dumps
NACE-CIP1-001 Free Study Guide! with New Update 100 Exam Questions
Are you aware of the target audience for the NACE CIP1-001 Exam?
The NACE CIP1-001 test is designed for professionals and students. The professionals need to be certified by the NACE CIP1-001 exam as they are going to work in any part of the world. They need a good skill set of knowledge in the coatings. The students can prepare themselves for the NACE CIP1-001 exam to get good marks. Real exam questions will help them to easily pass the NACE CIP1-001 exam. You can easily study with the help of the NACE CIP1-001 exam dumps as the exam dumps contain the latest and updated versions of the NACE CIP1-001 test. The payment fee will help the students to easily manage their time during the preparation.
NACE-CIP1-001 certification exam is a professional certification for coating inspectors who are seeking to advance their career in the field of corrosion protection. NACE-CIP1-001 exam is designed to test the candidate's knowledge and skills in the application of coating materials, surface preparation techniques, and inspection procedures for industrial structures and equipment.
NEW QUESTION # 35
ISO SA 2 is defined as:
- A. Very Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Near White Metal Blasting
- D. Thorough Blast Cleaning
Answer: D
NEW QUESTION # 36
Corrosion generally occurs at which of the following sites:
- A. Cathode
- B. Metallic pathway
- C. Electrolyte
- D. Anode
Answer: D
NEW QUESTION # 37
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC PA 2
- B. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- C. NACE SP 0178
- D. NACE SP 0188
Answer: B
NEW QUESTION # 38
Digital hygrometers
- A. consist of a bimetallic sensing element protected from wind gusts.
- B. determine relative humidity, air temperature, and dew point temperature:
- C. are used to measure temperature from a distance.
- D. use a thermocouple in contact with the surface to measure temperature
Answer: B
NEW QUESTION # 39
An Inspector should change position when:
- A. The Owner can save some money by the change
- B. The Inspector is convinced by verifiable facts
- C. The Inspectors position is not the majority position
- D. Only when directed by the supervisor
Answer: B
NEW QUESTION # 40
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 cm (1 inch)
- B. 2.5 millimeters (.10 inch)
- C. 6.35 cm (2.5 inch)
- D. 1 cm (.39 inch)
Answer: A
NEW QUESTION # 41
A successful coating inspector must be able to
- A. look for problems or issues during application.
- B. apply the coating with expert accuracy.
- C. advise the coating applicator on how to mix the coating.
- D. recommend the appropriate coating technique for the job to the contractor.
Answer: A
NEW QUESTION # 42
Conventional spray is a good choice when:
- A. High transfer efficiency is required
- B. High production rates are required
- C. High quality finishes are required
- D. High viscosity coatings are being applied
Answer: C
NEW QUESTION # 43
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. Treating metal with a liquid inhibiter
- C. A coating layer applied to the surface to inhibit corrosion
- D. Complete elimination pf the corrosion process
Answer: A
NEW QUESTION # 44
Which one of these elements is not necessary for corrosion to occur:
- A. Reference Cell
- B. Cathode
- C. Anode
- D. Electrolyte
Answer: A
NEW QUESTION # 45
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 225 Gauge Readings resulting in 75 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 105 Gauge Readings resulting in 35 Spot Measurements
Answer: A
NEW QUESTION # 46
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Near White Metal Blasting
- D. Very Thorough Blast Cleaning
Answer: D
NEW QUESTION # 47
The NACE Inspector should perform tests for soluble salts:
- A. When specified
- B. After surface preparation
- C. Prior to surface preparation
- D. Prior to coating application
Answer: A
NEW QUESTION # 48
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. vial lest.
- B. wet film thickness (WFT) measurement.
- C. dry film thickness (DEI) measurement.
- D. blotter test for the presence of oil and water.
Answer: D
NEW QUESTION # 49
The main responsibilities of the inspector are to
- A. observe and report the quality of the work performed.
- B. direct and perform the work stated in the specification.
- C. demonstrate to the contractor how to apply the coating.
- D. observe and direct the work of the contractors.
Answer: A
NEW QUESTION # 50
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Carefully review the document and do the best you can
- C. Hire a third patty to assist you in understanding the document
- D. Advise the owners' representative of your lack of knowledge in this area
Answer: B
NEW QUESTION # 51
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. how the item was coated.
- B. when the coating will be reapplied.
- C. what items were coated.
- D. what materials were used.
Answer: A
NEW QUESTION # 52
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to saturation level.
Answer: D
NEW QUESTION # 53
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 70% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 90% of the specified maximum thickness
Answer: C
NEW QUESTION # 54
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. pigment
- C. binder
- D. additive
Answer: C
NEW QUESTION # 55
Whenever dissimilar metals must join, the most common practice is to
- A. avoid coating all connected dissimilar metals.
- B. provide anodic protection to prevent corrosion.
- C. coat all connected dissimilar metals.
- D. provide cathodic protection to prevent corrosion,
Answer: C
NEW QUESTION # 56
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- B. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- C. Bring the matter up at the pre-job conference
- D. Default to the owner's Inspection and Test Plan
Answer: C
NEW QUESTION # 57
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Achieve consensus through negotiation
- C. Call the supervisor
- D. Never change his/her mind
Answer: C
NEW QUESTION # 58
......
In addition to the NACE-CIP1-001 Exam, NACE also offers certification programs for Coating Inspector Level 2 and Level 3. These programs are designed for individuals who have more experience in the coatings industry and are responsible for overseeing coating projects and training other inspectors. Each level of certification requires a higher level of experience and knowledge, and candidates must pass an exam to earn the certification.
Get up-to-date Real Exam Questions for NACE-CIP1-001: https://www.dumpsreview.com/NACE-CIP1-001-exam-dumps-review.html
Pass NACE-CIP1-001 Exam Latest Practice Questions: https://drive.google.com/open?id=12f9nd-L7nH3pL3aWk6ercomlIjgYx1JL
